Description

Insane Shafts High Performance Left Hand Rear CV Axle | 2008-2015 Mitsubishi Evo X GSR (IS-613) 1000HP

Firstly, Buy Insane Shafts 1000HP Left Hand Rear CV Axle Evo X IS-613 for 2008–2015 GSR models. Upgrade your Mitsubishi Lancer Evolution X rear drivetrain with the Insane Shafts High Performance Left Hand Rear CV Axle 1000HP for 2008–2015 Mitsubishi Evo X GSR. Designed for the left-hand rear, or driver-side, position, this high-performance axle is built for serious 4B11T applications that demand increased drivetrain strength.

The 1000HP Insane Shafts rear CV axle is manufactured from Chromoly steel and goes through a proprietary annealing and heat-treatment process. It then receives additional cryogenic treatment for increased strength. Insane Shafts designed these 1000HP axles for high-power vehicles and states that they have been tested under extreme conditions both on and off the track.

For a heavily modified Evo X, the rear axles can experience substantial loads. Increased engine power, high torque, aggressive launches, sticky tires, and track use can all increase stress throughout the drivetrain. This axle provides a performance-focused solution for the left rear position while retaining the factory-style application.

Insane Shafts 1000HP Left Hand Rear CV Axle

The Insane Shafts 1000HP Left Hand Rear CV Axle is designed for the rear driver-side position on the 2008–2015 Mitsubishi Evo X GSR. The application is for the manual-transmission, AYC-equipped Evo X GSR.

This is the high-power version of the Insane Shafts rear-left axle. It is designed for applications requiring substantially more axle capacity than a standard replacement.

The axle uses Chromoly steel as its foundation. Insane Shafts applies annealing and heat treatment before adding cryogenic treatment. This combination is intended to provide additional strength for high-horsepower drivetrain applications.

1000 Wheel Horsepower Capability

The 1000HP version is designed to handle power demands of up to 1000 wheel horsepower. That rating makes it intended for substantially modified Evo X builds rather than basic stock replacements.

A 1000 WHP-rated axle can be particularly relevant for high-output 4B11T vehicles using larger turbochargers, increased boost, upgraded engine components, high-grip tires, and aggressive driving setups.

Actual axle durability will depend on the entire vehicle configuration. Tire grip, launch technique, suspension setup, drivetrain condition, and driving environment can all affect the loads placed on a CV axle.

For that reason, the axle’s 1000 WHP rating should be considered as part of a complete drivetrain plan rather than as a guarantee of service life under every condition.

Chromoly Steel Construction

The IS-613 1000HP configuration uses Chromoly steel for high-strength performance applications. The material is processed through Insane Shafts’ proprietary annealing and heat-treatment procedures before receiving additional cryogenic treatment.

This multi-stage treatment is designed to increase the strength of the axle for demanding applications.

The result is a performance-oriented rear CV axle intended for Evo X owners who have moved beyond standard power levels and require additional drivetrain capacity.

Cryogenic Treatment for High-Power Applications

One of the key features of the 1000HP version is its additional cryogenic treatment.

According to the current product information, Insane Shafts’ 1000HP axles are cryogenically treated after the proprietary annealing and heat-treatment process. The manufacturer describes this process as providing additional strength for today’s high-horsepower vehicles.

This additional treatment separates the 1000HP configuration from the standard power application.

For an Evo X making serious power, selecting drivetrain components designed around the vehicle’s output can help create a more suitable overall performance package.

Left Hand Rear Application

This axle is designed for the left-hand rear, also known as the driver-side rear, position.

Correct side selection is important when ordering CV axles. The matching right-hand rear application is the Insane Shafts IS-614 family.

Buy Insane Shafts 1000HP Left Hand Rear CV Axle Evo X IS-613 for 2008–2015 GSR models, Shop high-performance Evo axles online.

The product is sold as one left-hand rear CV axle, so it is intended to replace the axle on one side of the vehicle.

If both rear axles need to be upgraded, the matching right-hand rear axle should be purchased separately.

2008–2015 Mitsubishi Evo X GSR Fitment

The 1000HP rear-left axle is designed for:

• 2008–2015 Mitsubishi Lancer Evolution X GSR
• 4B11T engine applications
• Manual transmission
• Rear AYC drivetrain
• Left-hand rear position
• Driver-side rear axle
• High-power applications up to 1000 WHP

Current application information identifies the axle for the 2008–2015 Mitsubishi Evo X GSR manual transmission with rear AYC.

Important: This axle is not intended for Evo X MR models. Buyers should verify their transmission and drivetrain configuration before ordering.

Built for High-Power Evo X Builds

A stock Evo X and a 1000 WHP Evo X place very different demands on their drivetrain components.

As 4B11T power increases, the rear CV axles must handle greater torque loads. Aggressive launches can increase those loads even further, especially when combined with high-grip tires and a performance-focused suspension setup.

The Insane Shafts 1000HP rear-left axle is designed for this type of high-performance environment.

It can be suited to:

• High-power 4B11T builds
• Large-turbo Evo X applications
• Drag racing vehicles
• Track-focused Evo X builds
• High-grip tire setups
• Aggressive street cars
• Competition-oriented applications
• Evo X vehicles producing up to 1000 WHP

The axle should be considered alongside the condition and specifications of the transmission, differential, driveshaft, hubs, suspension, and other drivetrain components.

ABS Ring and New Spindle Nut

Insane Shafts states that its axles include removable ABS rings where applicable and new spindle nuts.

The removable ABS ring allows the axle to accommodate the applicable ABS configuration. The new spindle nut also provides a fresh fastening component for installation.

Before installation, compare the replacement axle with the original component. Confirm the ABS configuration and other drivetrain details before completing the installation.

Product Features

• Insane Shafts high-performance rear CV axle
• 1000 WHP application
• Left-hand rear position
• Driver-side rear axle
• 2008–2015 Mitsubishi Evo X GSR
• 4B11T engine application
• Manual transmission
• Rear AYC drivetrain
• Chromoly steel construction
• Proprietary annealing process
• Proprietary heat treatment
• Additional cryogenic treatment
• Removable ABS ring where applicable
• New spindle nut included
• Sold individually
• Insane Shafts limited warranty

What’s Included?

The package includes:

1 × Insane Shafts 1000HP Left Hand Rear CV Axle

Insane Shafts also states that its axles include a removable ABS ring where applicable and a new spindle nut.

The axle is sold individually. A matching right-hand rear axle can be purchased separately when upgrading both sides.

Why Upgrade to a 1000HP Rear CV Axle?

High-powered Evo X builds place much greater demands on the drivetrain than a factory vehicle.

A large turbocharger and increased engine output can significantly increase torque through the drivetrain. High-grip tires can also increase the amount of force transferred through the axles during acceleration.

The Insane Shafts 1000HP Left Hand Rear CV Axle is designed specifically for this type of performance application.

Its Chromoly construction and multi-stage heat-treatment process provide a purpose-built solution for high-power Evo X owners. The additional cryogenic treatment further differentiates the 1000HP configuration from the standard axle application.

For a serious 4B11T build, selecting drivetrain components with an appropriate power rating is an important part of building a reliable and properly matched performance system.

Frequently Asked Questions

What is the Insane Shafts 1000HP rear-left CV axle?

It is a high-performance left-hand rear CV axle designed for the 2008–2015 Mitsubishi Evo X GSR manual AYC application, with a stated capacity of up to 1000 WHP.

Which side does this axle fit?

It fits the left-hand rear, also known as the driver-side rear position.

How much power is the 1000HP axle rated for?

The 1000HP version is designed to handle power demands of up to 1000 wheel horsepower.

What is the axle made from?

The axle is made from Chromoly steel and receives proprietary annealing and heat treatment, followed by additional cryogenic treatment for the 1000HP application.

Does it fit the Evo X MR?

No. The listed application is the Evo X GSR, and current product information states that these axles do not fit MR models.

Does it fit manual Evo X GSR models?

Yes. The application is listed for the 2008–2015 Evo X GSR manual-transmission AYC drivetrain.

Is the axle sold individually?

Yes. The package contains one left-hand rear CV axle.

Is a new spindle nut included?

Yes. Insane Shafts states that its axles include new spindle nuts.

Does it include an ABS ring?

A removable ABS ring is included where applicable, according to the product information. For Evo X GSR owners building a serious high-power 4B11T drivetrain, the Insane Shafts High Performance Left Hand Rear CV Axle 1000HP combines Chromoly construction, advanced heat treatment, and additional cryogenic treatment in a purpose-built driver-side rear axle, available to order from evomotorparts.com.

Buy Insane Shafts 1000HP Left Hand Rear CV Axle Evo X IS-613 for 2008–2015 GSR models, Shop high-performance Evo axles online.